Practicality features of the Burgman include cubby holes for your wallet and phone as well as a massive Cars Motorcycles Trucks. View All 7 Photos. Glass Sparkle Black. View More Videos. Italjet Dragster P, Kymco Like i P, - P, Kymco Like Italia E3 P79, Kymco AK P, Refer to the SDS operation manual for further details. If OK, then check the main relay. If the fuel pump motor does not make operating sound, inspect the fuel pump circuit connections or inspect the main relay and tip-over sensor.
Do not disassemble it other than shown in this manual. Never remove the throttle valve B. Avoid removing the throttle stop screw C. The throttle stop screw C is factory-adjusted at the time of delivery and therefore avoid removing or turn- ing it unless otherwise necessary.
Any service on the exhaust system should be performed when the system is cool. If dirt is excessive, wash with water. It may cause damage if it gets a sharp impact. If the thermostat valve opening temperature is not within the specified range, replace the thermostat with a new one.
Thermostat valve opening temperature: Standard: Approx. If engine oil is leaking, visually inspect the oil seal and O-ring. If engine coolant is leaking, visually inspect the mechanical seal and seal washer.
Align the boss A of the water pump shaft end with the slot B of the oil pump shaft. NOTE: To prevent the pawl 2 from damage, insert the fastener all the way into the installation hole. Take care not to bend the radiator fins. Hang the brake caliper on the frame with a string etc. If the length is found shorter than the service limit, replace the spring with a new one. Make sure that the stopper ring is securely fitted into the groove on the outer tube.
Check the bearings and races for corrosion, nick or other dam- age. If any abnormal condition is noted, replace the damaged part with a new one. Do not use mix different types of fluid such as silicone-based or petroleum-based.
Never reuse brake fluid left over from the last servicing or stored for long periods. If any abnormal condition is noted, replace it with a new one.
Inspect the caliper bracket 1 for any damage. Inspect the rubber boots 2 for any damage. Measure the disc thickness at several positions using a micrometer. If the measurement is less than the service limit or any abnormal condition is noted, replace the disc with a new one.
For this reason, it is recommended to use a tire changer that can satisfy this sealing requirement and can make the operation efficient as well as functional. NOTE: If the external appearance of the valve shows no abnormal con- dition, removing of the valve is not necessary.
The line must be equidistant from the wheel rim all around. If the distance between the rim line and wheel rim varies, this indicates that the bead is not properly seated. If this is the case, deflate the tire completely and unseat the bead for both sides. Neglecting proper procedure may cause damage to this part. Improper use can cause damage to the motorcycle and tester.
Are accessories being installed? Remove accessories. Step 2 1 Check the battery for current leaks. Go to Step 3. Go to Step 5. Go to Step 6. If the resistance is out of specified value, replace the stator with a new one. Starter motor will not run. Is a voltage OK? Go to Step 4. If any damages are found, replace the brush assembly with a new one. Make sure that the length A is not less than 3. If this length becomes less than 3.
If the interlock system does not operate properly, check each component for damage or abnormalities. If any abnormality is found, replace the component with a new one. If no continuity is noted, the relay must be replaced. Is the voltage OK? Measure the ignition coil resistance in both the primary and sec- ondary windings.
If the resistance is not within the standard range, replace the ignition coil with a new one. If coupler the resistance is not as specified, the CKP sensor must be replaced. When disconnecting and reconnecting the speedome- ter coupler, make sure to turn OFF the ignition switch, or electronic parts may get damaged.
If any abnormal condition is noted, replace the switch. Never remove the container from the battery. If any signs of cracking or electrolyte leakage from the sides of the battery have occurred, replace the battery with a new one.
If the battery terminals are found to be coated with rust or an acidic white powdery substance, clean the battery terminals with sandpaper. Valve clearance out of adjustment Adjust. Poor seating of valves Replace or repair. Defective valve guides Replace. Worn rocker arms or cam surfaces Replace.
Too large valve clearance Adjust. Weakened or broken valve springs Replace. Worn rocker arm or cam surface Replace. Worn and burnt camshaft journal Replace. Weakened valve springs Replace. Worn camshaft Replace. Valve timing out of adjustment Adjust. Too narrow spark plug gap Adjust. Loss of valve clearance Adjust.
Worn piston rings or cylinder Replace. Heavy carbon deposit on piston crown Clean. Not enough oil in the engine Add oil. Defective oil pump or clogged oil circuit Replace or clean.
Overtightened steering stem nut Adjust. Broken bearing in steering stem Replace. Distorted steering stem Replace. Not enough pressure in tires Adjust. Wobbly handlebars 1. Loss of balance between right and left front forks Replace. Leakage of brake fluid from hydraulic system Repair or replace.
Worn pads or disc Replace. Oil adhesion on friction surface of pads Clean disc and pads. Defective ignition coil Replace.
Defective spark plug Replace. Defective CKP sensor Replace. Defective ECM Replace. Defective TO sensor Replace. Open-circuited wiring connections Repair or replace. Cracked battery case Replace the battery. Battery has been left in a run-down condition for a Replace the battery. Do not protrude the HO2 sensor lead wire from the frame. Tighten the front axle nut to the specified torque 2 Cable guide after touching the stopper of speedometer gear box to the stopper of front fork outer tube.
An unleaded gasoline type is recom- mended.
0コメント